SmartDFE v4.4 Release Notes
New Features and Bug Fixes
| Jira Story | Description |
| SDFE-1492 | As an OPC user, I would like information about an SMD before I install it and optionally provide a new name when I do install it |
| SDFE-1671 | Streamline iHVD Analysis should be performed with the postscript and ICC profiles that will be used by the RIP Server |
| SDFE-1674 | Update colours for RIP Ahead 'Total estimated space required" at above 80% |
| SDFE-1728 | Integrate new Direct with changes for RIPAhead/ScreenDirect mode |
| SDFE-1730 | Integrate changes to support SLD Train |
| SDFE-1735 | As a user, I would like an Enable Autotune toggle and have this accessible over OPC |
| SDFE-1738 | Add default Streamline model to the Evaluation version of SPC |
| SDFE-1748 | As a user, I would like the Streamline pane to be redesigned to work with the updated Streamline Direct |
| SDFE-1750: | As a user, I don't want to know about iHVD, it should just be set by Streamline Autotune when it makes sense |
| SDFE-1756: | As an OPC user, I would like to be able to change the mode (RipDirect/RipAhead/ScreenDirect) over OPC UA |
| SDFE-1782 | When I launch SPC, I expect the connections to go green if my RIP Server is running its Start script |
| SDFE-1784 | Pass jobname to the RIP Server when a job is submitted so it can be used in output filenames |
| SDFE-1817 | Relaxed the requirement for the print speed needing to match when comparing the current Printer Profile with a Smart Media |
| SDFE-1823 | Integrate new Direct (2023_06_21_RC1) with Harlequin Core 13.2r6 |
| SDFE-1824 | Integrate new Direct v4.0 with memory management |
| SDFE-1828: | Integrate Streamline Direct release with latest Mako |
| SDFE-1859: | As a user, I would like to see the RGB representation of inks when selecting them and access these values over OPC |
| SDFE-1170 | Fixed a bug where the Print Run does not Autostop when using 'Add Job Information Page' with RIP Ahead |
| SDFE-1729 | Fixed a bug where clicking Revert prevents changes to custom settings from taking effect |
| SDFE-1731 | Fixed a bug with Tone Curves values were not being set correctly in the UI |
| SDFE-1761 | Fixed a bug where the mode for printing targets could stay on if a RemotePrint did not complete |
| SDFE-1811 | Fixed a bug where the OPC UA property AllMedia/SelectedName receives InvalidOperationException |
| SDFE-1826 | Fixed a bug where the progress bar in the Print Queue was being slightly cropped at the right |
| SDFE-1858 | Fixed a bug where edited Tone Curves were having the reverse effect to what is intended |
| SDFE-1860 | Fixed a bug where the Examine preprocessing step was not always completing successfully |
| SDFE-1877 | Fixed a bug where remote directories were not being created reliably when Applying settings |
| SDFE-1879 | Fixed a bug where it was possible to load an invalid tone curve |
| SDFE-1880 | Fixed a bug where OPC UA AllMedia/SelectedName receives InvalidOperationException |
| SDFE-1882 | Fixed a bug where SPC was sometimes reporting the incorrect active job over OPC |
| SMQ-70 | Simple ICC profile generation |
| SMQ-82 | As a user I want a 3D gamut view in Smart Calibrator. |
| SMQ-197 | Cosmetic changes to the ICC profiling UI in Smart Calibrator. |
| SMQ-11 | Change a spot colour using CMYKOV sliders |
| SMQ-15 | Warned when the spot colour is out of gamut |
| SMQ-16 | Out of gamut spot colour to be automatically mapped in gamut. |
| SMQ-84 | A spot colour to show the before and after colour in the preview |
| SMQ-90 | Choose the Delta E formula i.e. 1976 0r 2000 |
| SMQ-91 | Set the delta E tolerance for out of gamut warnings |
| SMQ-92 | View delta E when a spot is out of gamut |
Known Limitations
- Job names with more than 50 characters are unsupported, but the user is not prevented from exceeding this limit.
- Job names with characters that would be illegal in a filename can cause failures when doing file-based output.
CoPra
CXCProfiler.exe not automatically picking up license from installed CoPra.
For this you will need:-
- the path where Smart Calibrator is installed.
- a Copra License and the location of the license.
1. Open up the command line
2. Change the directory to where you have installed calibrator. This will usually look something like -> cd C:\Program Files\Smart Calibrator
3. Finally input this command -> CXCProfiler.exe license C:\Address\CopraLicense.lic
This will license CXCProfiler.exe and enable ICC profile to be created in Smart Calibrator.